Wincor Nixdorf BEETLE AT COM Board Guía de usuario

BEETLE AT COM BoardBenutzerhandbuch/User Guide

Installation of COM7 and COM8If you want to activate the (optional) interfaces COM7 and COM8 first fix the chip (see illustration). Please take care t

Installation in the BEETLE /60, BEETLE /LInstall the COM board in a free slot of your BEETLE POS system. Refer tothe documentation of your POS system

I/O AdressesThe I/O addresses are adjusted by means of I/O1-I/O3 jumpers.JumperIO1= openIO2= openIO3= openDEFAULTIO1= closedIO2= openIO3= openIO1= ope

InterruptsThe interrupts are also set by means of jumpers. In total there are 15interrupts (IRQ) in a PC system. The interrupts IRQ1 - IRQ8, IRQ13 and

Example 1: COM5 to IR9 and COM6 - 8 shared to IRQ10. Plug in jumperI9, IR9, I12 and IR10.Example 2: COM5 to IRQ12, COM6 to IRQ15 and COM7 - 8 shared t

Assignment of COM Port Addresses andInterruptsEnsure that there is no conflict of hardware port addresses or interruptrequests (IRQs) used by your sys

BEETLE systems factory settings provide to use shared IRQ10 for COM3and COM4, but COM4 can be configured by jumpers on the motherboard touse IRQ11 ins

Ad ding COM ports un der Wind ows 9xTo add a COM port to your system configuration, run the “Add NewHardware” wizard. It is not recommendable to run t

Using sha red in ter rupts for COM ports withWind ows NTSharing an interrupt for a COM port under Windows NT requires a specificconfiguration in the

Proceed very carefully as wrong entries in the registry could preventWindows NT from starting! Therefore, you should save your registry before.Hint: ‘

Ihre Meinung/ Youropinion:Uns interessiert IhreMeinung zu dieserDruckschrift.Schicken Sie uns bitte eineInformation, wenn Sie unskonstruktive Hinweise

PIN AssignmentPIN# SIGNAL COM6 SIGNAL COM51 +P12V +P12V2 RxD RxD3 TxD TxD4 DTR DTR5 GND GND6 DSR DSR7 RTS RTS8 CTS CTS9 +P5V +P5VCOM7 and COM8 can be

The internal connector assignment of the COM7 and COM8 is as follows: PIN# COM7, COM8 intern1 +P5V2 GND3 DCD4 GND5 CTS6 DTR7 RTS8 TxD9 DSR10 RxD11 RI1

Technical Datan AT plug-in board, half length, ISA bus in ter fa ce; ISA bus 8 bitn 2 COM in ter fa ces:COM5*, COM6* with + 5 V/+ 12 V po wer supp l

Herausgegeben von/Published by Wincor Nixdorf International GmbHD-33094 PaderbornBestellnummer/Order No. 0175 0000 183GPrinted in Germany

AT COM BoardUser ManualEdition April 2008

Co py right© Win cor Nix dorf In ter na tio nal GmbH, 2008The re pro duc ti on, trans mis si on or use of this do cu ment or its con tents is not

ContentsManufacturer’s Cer ti fi ca te ...1Im por tant No tes ...1War ran ty ...

Manufacturer’s CertificateThis device meets the requirements of EU Guidelines 2004/108/EC“Electromagnetic Compatibility“ and 2006/95/EC ”Low Voltage D

All parts of the pro duct which are sub ject to wear and tear are not in clu dedin the war ran ty en ga ge ment.Plea se or der spa re parts at the

IntroductionThe BEETLE AT COM board is a half-length, plug-in board for BEETLE POS systems.The COM board provides you with two additional power-suppli